Yamaha VMAX VMX12P Скачать руководство пользователя страница 85

Страница: 85 / 125

PERIODIC MAINTENANCE AND MINOR REPAIR

6-34

EAU02939

Checking the front fork

The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.

To check the condition

EW000115

WARNING

Securely support the motorcycle so
that there is no danger of it falling
over.

Check the inner tubes for scratches,
damage and excessive oil leakage.

To check the operation

1. Place the motorcycle on a level

surface and hold it in an upright
position.

2. While applying the front brake,

push down hard on the handle-
bars several times to check if the
front fork compresses and re-
bounds smoothly.

EC000098

CAUTION:

If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.

u5gk12.book Page 34 Wednesday, June 13, 2001 8:55 AM

Содержание VMAX VMX12P






























































































































Результаты поиска

Содержание VMAX VMX12P

Отзывы:

Бренды по названию

Популярные бренды

Yamaha VMAX VMX12P, Руководство пользователя

Результаты поиска

Содержание VMAX VMX12P

Отзывы:

Бренды по названию

Популярные бренды