manualshive.com logo in svg

Yamaha VMAX VMX12P, Руководство пользователя

Поделиться
Скачать
Yamaha VMAX VMX12P Скачать руководство пользователя страница 26

INSTRUMENT AND CONTROL FUNCTIONS

3-5

3

EAU00152

Clutch lever 

The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handle-
bar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-17 for an explanation of the ignition
circuit cut-off system.)

EAU00157

Shift pedal 

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 5-speed con-
stant-mesh transmission equipped on
this motorcycle.

EAU00158

Brake lever 

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

1. Clutch lever

1. Shift pedal

1. Brake lever

u5gk12.book  Page 5  Wednesday, June 13, 2001  8:55 AM

Содержание VMAX VMX12P






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды