Yamaha VMAX VMX12P Скачать руководство пользователя страница 31

Страница: 31 / 125

INSTRUMENT AND CONTROL FUNCTIONS

3-10

2. Remove the bolts and screws, and

then pull the rider seat off.

To install the rider seat

1. Insert the projection on the front of

the rider seat into the seat holder
as shown.

2. Place the rider seat in the original

position, and then tighten the bolts
and screws.

NOTE:

Make sure that the seat is properly se-
cured before riding.

3. Return the rider seat backrest to

the original position.

EAU00260

Helmet holder

To open the helmet holder, insert the
key into the lock, and then turn the key
as shown.
To lock the helmet holder, place it in
the original position, and then remove
the key.

EW000030

WARNING

Never ride with a helmet attached to
the helmet holder, since the helmet
may hit objects, causing loss of
control and possibly an accident.

1. Bolt (

2. Screw (

1. Projection
2. Seat holder

1. Helmet holder
2. Unlock.

u5gk12.book Page 10 Wednesday, June 13, 2001 8:55 AM

Содержание VMAX VMX12P






























































































































Результаты поиска

Содержание VMAX VMX12P

Отзывы:

Похожие инструкции для VMAX VMX12P

Бренды по названию

Популярные бренды

Yamaha VMAX VMX12P, Руководство пользователя

Результаты поиска

Содержание VMAX VMX12P

Отзывы:

Похожие инструкции для VMAX VMX12P

Бренды по названию

Популярные бренды