manualshive.com logo in svg

Yamaha VMAX VMX12P, Руководство пользователя

Поделиться
Скачать
Yamaha VMAX VMX12P Скачать руководство пользователя страница 52

6-1

6

EAU00462

6-

PERIODIC MAINTENANCE AND MINOR REPAIR  

EAU01790

Safety is an obligation of the owner.
Periodic inspection, adjustment and lu-
brication will keep your vehicle in the
safest and most efficient condition pos-
sible. The most important points of
motorcycle inspection, adjustment, and
lubrication are explained on the follow-
ing pages.

Maintenance, replacement, or repair
of the emission control devices and
systems may be performed by any
repair establishment or individual
that is certified (if applicable).

EW000060

WARNING

@ 

If you are not familiar with motor-
cycle maintenance work, have a
Yamaha dealer do it for you. 

@

EAU00467

PERIODIC MAINTENANCE 

PROPER PERIODIC MAINTENANCE
OF YOUR MOTORCYCLE IS IMPOR-
TANT IN ORDER TO ENJOY LONG,
PLEASURABLE SERVICE. ESPE-
CIALLY IMPORTANT ARE THE
MAINTENANCE SERVICES RELAT-
ED TO EMISSIONS CONTROL.
THESE CONTROLS NOT ONLY
FUNCTION TO ENSURE CLEANER
AIR, BUT ARE ALSO VITAL TO
PROPER ENGINE OPERATION AND
MAXIMUM PERFORMANCE. IN THE
FOLLOWING PERIODIC MAINTE-
NANCE CHARTS, THE SERVICES
RELATED TO EMISSIONS CON-
TROL ARE GROUPED SEPARATE-
LY. THESE SERVICES REQUIRE
SPECIALIZED DATA, KNOWLEDGE,
AND EQUIPMENT. YAMAHA DEAL-
ERS ARE TRAINED AND EQUIPPED
TO PERFORM THESE PARTICULAR
SERVICES. 

EAU01659

Owner’s tool kit 

The tool kit is located inside the storage
compartment behind the rider seat
backrest. (See page 3-9 for an expla-
nation on moving the rider seat back-
rest forward and back.)

1. Owner’s tool kit
2. Rider seat backrest

u5gk12.book  Page 1  Wednesday, June 13, 2001  8:55 AM

Содержание VMAX VMX12P






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды