Yamaha VMAX VMX12P Скачать руководство пользователя страница 70

Страница: 70 / 125

PERIODIC MAINTENANCE AND MINOR REPAIR

6-19

7. Remove the cylinder drain plug

covers on the outside of the cylin-
der blocks by removing the
screws.

8. Remove the rubber coolant drain

plugs to drain the coolant from the
engine.

9. After the coolant is completely

drained, thoroughly flush the cool-
ing system with clean tap water.

10. Install the water pump drain bolt,

and then tighten it to the specified
torque.

NOTE:

Check the washer for damage and re-
place it if necessary.

11. Install the rubber coolant drain

plugs, and then install the cylinder
drain plug covers.

NOTE:

Check the rubber plugs for damage
and replace them if necessary.

12. Turn the coolant drain cock to

“OFF”.

13. Pour the recommended coolant

into the reservoir to the maximum
level, and then install the cap.

14. Pour the recommended coolant

into the radiator until it is full.

1. Screw (

1. Rubber coolant drain plug (

Tightening torque:

Water pump drain bolt:

43 Nm (4.3 m·kgf, 31 ft·lb)

u5gk12.book Page 19 Wednesday, June 13, 2001 8:55 AM

Содержание VMAX VMX12P






























































































































Результаты поиска

Содержание VMAX VMX12P

Отзывы:

Похожие инструкции для VMAX VMX12P

Бренды по названию

Популярные бренды

Yamaha VMAX VMX12P, Руководство пользователя

Результаты поиска

Содержание VMAX VMX12P

Отзывы:

Похожие инструкции для VMAX VMX12P

Бренды по названию

Популярные бренды