manualshive.com logo in svg

Yamaha MAJESTY YP250, Руководство пользователя

Поделиться
Скачать
Yamaha MAJESTY YP250 Скачать руководство пользователя страница 81

6-30

PERIODIC MAINTENANCE AND MINOR REPAIR

6

8

Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking perfor-
mance.

8

Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will signifi-
cantly lower the boiling point of
the fluid and may result in vapor
lock.

8

Brake fluid may deteriorate paint-
ed surfaces or plastic parts.
Always clean up spilled fluid
immediately.

8

As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if
the brake fluid level goes down
suddenly, have a Yamaha dealer
check the cause.

EAU02962

Checking and lubricating the
cables

Cables, checking and lubricating

The operation of all control cables
and the condition of the cables
should be checked before each ride,
and the cables and cable ends
should be lubricated if necessary.  If
a cable is damaged or does not move
smoothly, have a Yamaha dealer
check or replace it.

EW000112

w

Damage to the outer sheath may
interfere with proper cable opera-
tion and will cause the inner cable
to rust. Replace a damaged cable
as soon as possible to prevent
unsafe conditions.

EAU03976

Changing the brake fluid

Brake fluid, changing

Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte-
nance and lubrication chart. In addi-
tion, have the oil seals of the master
cylinders and calipers as well as the
brake hoses replaced at the intervals
listed below or whenever they are
damaged or leaking.

8

Oil seals: Replace every two
years.

8

Brake hoses: Replace every four
years.

Recommended lubricant:

Engine oil

5SJ-28199-E2  8/9/02 4:06 PM  Page 79

Содержание MAJESTY YP250





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды