manualshive.com logo in svg

Yamaha MAJESTY YP250, Руководство пользователя

Поделиться
Скачать
Yamaha MAJESTY YP250 Скачать руководство пользователя страница 66

6-15

PERIODIC MAINTENANCE AND MINOR REPAIR

6

3. Wait a few minutes until the oil

settles, remove the oil filler cap,
wipe the dipstick clean, insert it
back into the oil filler hole (with-
out screwing it in), and then
remove it again to check the oil
level.

NOTE:

The engine oil should be between the
minimum and maximum level marks.

3

1

2

1

1.

Engine oil filler cap

2.

Maximum level mark

3.

Minimum level mark

To change the engine oil

1. Start the engine, warm it up for

several minutes, and then turn it
off.

2. Place an oil pan under the

engine to collect the used oil.

3. Remove the engine oil filler cap

and the engine oil drain bolt to
drain the oil from the crankcase.

1

1.

Engine oil drain bolt

4. If the engine oil is below the min-

imum level mark, add sufficient
oil of the recommended type to
raise it to the correct level.

5. Insert the dipstick into the oil filler

hole, and then tighten the oil filler
cap.

5SJ-28199-E2  8/9/02 4:06 PM  Page 64

Содержание MAJESTY YP250





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды