manualshive.com logo in svg

Yamaha MAJESTY YP250, Руководство пользователя

Поделиться
Скачать
Yamaha MAJESTY YP250 Скачать руководство пользователя страница 46

5-1

EAU00372

OPERATION AND IMPORTANT RIDING POINTS

5

EAU01118

w

8

8

Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or func-
tion that you do not thorough-
ly understand.

8

8

Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.

8

8

For safety, always start the
engine with the centerstand
down.

EAU03843

Starting the engine

Starting the engine

EC000046

c

C

See page 5-4 for engine break-in
instructions prior to operating the
vehicle for the first time.

In order for the ignition circuit cut-off
system to enable starting, the side-
stand must be up.

EW000054

w

8

8

Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-22.

8

8

Never ride with the sidestand
down.

1. Turn the key to “ON” and make

sure that the engine stop switch
is set to “

#

”.

2. Close the throttle completely.
3. Start the engine by pushing the

start switch while applying the
front or rear brake.

3

2

1

1.

Start switch

2.

Front brake lever

3.

Rear brake lever

5SJ-28199-E2  8/9/02 4:05 PM  Page 44

Содержание MAJESTY YP250





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды