Yamaha MAJESTY YP250 Скачать руководство пользователя страница 72

Страница: 72 / 116

6-21

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU03627

Air filter and V-belt case air
filter elements

Air filter and V-belt case air filter elements, cleaning

The air filter and V-belt case air filter
elements should be cleaned at the
intervals specified in the periodic
maintenance and lubrication chart.
Clean both filter elements more fre-
quently if you are riding in unusually
wet or dusty areas.

EC000092

Make sure that each filter ele-
ment is properly seated in its
case.

The engine should never be
operated without the filter ele-
ments installed, otherwise the
piston and/or cylinder may
become excessively worn.

4. Check the sponge material for

damage and replace it if neces-
sary.

5. Allow the sponge material to dry.
6. Apply oil of the recommended

type to the entire surface of the
sponge material, and then
squeeze the excess oil out.

Cleaning the air filter element

1. Place the scooter on the center-

stand.

2. Remove the air filter case cover

by removing the screws.

3. Pull the sponge material out

along with the mesh sheet, clean
it with solvent, and then squeeze
the remaining solvent out.

Air filter case cover

Screw (

Sponge material

Mesh sheet

5SJ-28199-E2 8/9/02 4:06 PM Page 70

Содержание MAJESTY YP250





















































































































Результаты поиска

Содержание MAJESTY YP250

Отзывы:

Бренды по названию

Популярные бренды

Yamaha MAJESTY YP250, Руководство пользователя

Результаты поиска

Содержание MAJESTY YP250

Отзывы:

Бренды по названию

Популярные бренды