Yamaha FZ6-NV Скачать руководство пользователя | Manualshive

Страница: 57 / 90

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-17

6

EAU36500

Adjusting the rear brake light
switch

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, have a Yamaha dealer ad-
just the brake light switch.

EAU22390

Checking the front and rear
brake pads

The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.

EAU22420

Front brake pads

Each front brake pad is provided with a
wear indicator groove, which allows
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator groove. If a brake
pad has worn to the point that the wear

indicator groove has almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.

EAU22500

Rear brake pads

Check each rear brake pad for damage
and measure the lining thickness. If a
brake pad is damaged or if the lining
thickness is less than 1.0 mm (0.04 in),
have a Yamaha dealer replace the
brake pads as a set.

1. Rear brake light switch

2. Rear brake light switch adjusting nut

1. Brake pad wear indicator groove

1. Lining thickness

U1B322E0.book Page 17 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
55
56
57
58
59
...
»

Содержание FZ6-NV



























































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6-NV

Бренд: LAZER Страницы: 19

Бренд: Yamaha Страницы: 124

Бренд: HYOSUNG Страницы: 199

Body Protector 4.5 Junior

Бренд: Leatt Страницы: 40

Бренд: Memphis Shades Страницы: 2

Бренд: Honda Страницы: 127

Бренд: Yamaha Страницы: 287

Бренд: Yamaha Страницы: 109

Бренд: Denali Страницы: 3

Бренд: Benelli Страницы: 314

Бренд: OKBABY Страницы: 35

Бренд: Bushtec Страницы: 28

Бренд: KTM Страницы: 32

Бренд: Troy Lee Designs Страницы: 53

Бренд: Honda Страницы: 119

Бренд: Honda Страницы: 150

Бренд: SHOEI Страницы: 42

Raider XL 2014+

Бренд: lehman Trikes Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды