Yamaha FZ6-NV страница 69 Скачать руководство пользователя

Страница: 69 / 90

PERIODIC MAINTENANCE AND MINOR REPAIR

6-29

5. Install the headlight bulb cover,

and then connect the coupler.

6. Install the headlight unit by install-

ing the bolts.

7. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU32822

Replacing the tail/brake light
bulb

1. Remove the seat. (See page

3-13.)

2. Remove the socket (together with

the bulb) by turning it counter-
clockwise.

WARNING

EWA12301

Do not touch the muffler bracket un-
til the exhaust system has cooled.

3. Remove the defective bulb by

pushing it in and turning it counter-
clockwise.

4. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

5. Install the socket (together with the

bulb) by turning it clockwise.

6. Install the seat.

1. Do not touch the glass part of the bulb.

1. Tail/brake light bulb socket

2. Muffler bracket cover

U1B322E0.book Page 29 Wednesday, August 24, 2005 3:17 PM

ProCarManuals.com

Содержание FZ6-NV



























































































Результаты поиска

Содержание FZ6-NV

Отзывы:

Похожие инструкции для FZ6-NV

Бренды по названию

Популярные бренды

Yamaha FZ6-NV, Руководство пользователя

Результаты поиска

Содержание FZ6-NV

Отзывы:

Похожие инструкции для FZ6-NV

Бренды по названию

Популярные бренды