Yamaha FZ6-NV Скачать руководство пользователя | Manualshive

Страница: 31 / 90

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-15

3

the following information before
handling the shock absorber. The
manufacturer cannot be held re-
sponsible for property damage or
personal injury that may result from
improper handling.

●

Do not tamper with or attempt to
open the gas cylinder.

●

Do not subject the shock ab-
sorber to an open flame or other
high heat sources, otherwise it
may explode due to excessive
gas pressure.

●

Do not deform or damage the
gas cylinder in any way, as this
will result in poor damping per-
formance.

●

Always have a Yamaha dealer
service the shock absorber.

EAU15301

Sidestand

The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.

NOTE:

The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)

WARNING

EWA10240

The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly as described

below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.

U1B322E0.book Page 15 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
29
30
31
32
33
...
»

Содержание FZ6-NV



























































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6-NV

Бренд: 3M Страницы: 26

Бренд: Cannondale Страницы: 102

Бренд: KAYO MOTOR Страницы: 74

Бренд: KAYO MOTO Страницы: 5

F 850 GS Adventure 2019

Бренд: BMW Motorrad Страницы: 346

Бренд: Honda Страницы: 201

GT650SR - PARTS CATALOGUE

Бренд: HYOSUNG Страницы: 124

Бренд: Crivit Страницы: 30

Бренд: National Cycle Страницы: 2

Бренд: Suzuki Страницы: 24

Бренд: Suzuki Страницы: 31

Бренд: Suzuki Страницы: 74

Бренд: Suzuki Страницы: 37

Бренд: Suzuki Страницы: 125

Бренд: Suzuki Страницы: 353

Бренд: Suzuki Страницы: 355

Бренд: Suzuki Страницы: 352

Бренд: Suzuki Страницы: 399

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды