Yamaha FZ6-NV Скачать руководство пользователя

Страница: 29 / 90

INSTRUMENT AND CONTROL FUNCTIONS

3-13

EAU32980

Seat

To remove the seat

1. Insert the key into the seat lock,

and then turn it counterclockwise.

2. While holding the key in that posi-

tion, lift the rear of the seat up, and
then pull the seat off.

To install the seat

1. Insert the projection on the front of

the seat into the seat holder as
shown.

2. Push the rear of the seat down to

lock it in place.

3. Remove the key.

NOTE:

Make sure that the seat is properly se-
cured before riding.

EAU14451

Storage compartment

The storage compartment is located
under the seat. (See page 3-13.)

WARNING

EWA10961

●

Do not exceed the load limit of 3
kg (7 lb) for the storage com-
partment.

●

Do not exceed the maximum
load of 196 kg (432 lb) for the ve-
hicle.

When storing the owner’s manual or
other documents in the storage com-
partment, be sure to wrap them in a
plastic bag so that they will not get wet.

1. Seat lock

2. Unlock.

1. Projection
2. Seat holder

1. Storage compartment

U1B322E0.book Page 13 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

Содержание FZ6-NV



























































































Результаты поиска

Содержание FZ6-NV

Отзывы:

Похожие инструкции для FZ6-NV

Бренды по названию

Популярные бренды

Yamaha FZ6-NV, Руководство пользователя

Результаты поиска

Содержание FZ6-NV

Отзывы:

Похожие инструкции для FZ6-NV

Бренды по названию

Популярные бренды