Yamaha FZ6-NV Скачать руководство пользователя | Manualshive

Страница: 37 / 90

background image

OPERATION AND IMPORTANT RIDING POINTS

5-1

5

EAU15950

WARNING

EWA10270

●

Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly un-
derstand.

●

Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.

●

Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.

EAU33721

Starting the engine

In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:

●

The transmission is in the neutral
position.

●

The transmission is in gear with
the clutch lever pulled and the sid-
estand up.

WARNING

EWA10290

●

Before starting the engine,
check the function of the igni-
tion circuit cut-off system ac-
cording to the procedure
described on page 3-16.

●

Never ride with the sidestand
down.

1. Turn the key to “ON” and make

sure that the engine stop switch is
set to “

”.

CAUTION:

ECA12741

The following warning lights and in-
dicator light should come on for a
few seconds, then go off.

●

Oil level warning light

●

Engine trouble warning light

●

Immobilizer system indicator
light

If a warning or indicator light does
not go off, see page 3-3 for the corre-
sponding warning and indicator
light circuit check.

2. Shift the transmission into the neu-

tral position.

NOTE:

When the transmission is in the neutral
position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical cir-
cuit.

3. Start the engine by pushing the

start switch.

NOTE:

If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the en-
gine more than 10 seconds on any one
attempt.

U1B322E0.book Page 1 Monday, August 8, 2005 1:49 PM

ProCarManuals.com

«
...
35
36
37
38
39
...
»

Содержание FZ6-NV



























































































Отзывы:

Нет отзывов

Похожие инструкции для FZ6-NV

Бренд: Sachs Bikes Страницы: 83

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 57

Бренд: Yamaha Страницы: 288

TRACER 700 2020

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 118

XV1700PCR Road Star Warrior

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 429

Бренд: Yamaha Страницы: 427

Moto matrix YZF-R6S

Бренд: Yamaha Страницы: 41

Бренд: N-Com Страницы: 6

Бренд: Honda Страницы: 186

Бренд: Ducati Страницы: 123

990D0-44G00-ALM

Бренд: Suzuki Страницы: 24

Бренд: DYNATEK Страницы: 8

Бренд: Yamaha Страницы: 400

2007 PAMPERA 450

Бренд: GAS GAS Страницы: 66

Бренд: SpeedAngle Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды