Yamaha FZ1 FZS1000N Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 123

Yamaha FZ1 FZS1000N Скачать руководство пользователя страница 84

PERIODIC MAINTENANCE AND MINOR REPAIR

6-33

6

EAU03297

Checking and lubricating the
cables

The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.

EW000111

WARNING

_

Damage to the outer housing of ca-
bles may result in internal rusting
and cause interference with cable
movement. Replace damaged ca-
bles as soon as possible to prevent
unsafe conditions.

_

EAU03370

Checking and lubricating the
brake and shift pedals

The operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu-
bricated if necessary.

EAU03164

Checking and lubricating the
brake and clutch levers

The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be lu-
bricated if necessary.

Recommended lubricant:

Yamaha Chain and Cable Lube
or engine oil SAE 10W-30
(API SE)

Recommended lubricant:

Lithium-soap-based grease
(all-purpose grease)

Recommended lubricant:

Lithium-soap-based grease
(all-purpose grease)

U5LV10.book Page 33 Wednesday, October 23, 2002 2:45 PM

«
...
82
83
84
85
86
...
»

Содержание FZ1 FZS1000N




























































































































Отзывы:

Нет отзывов