Yamaha FZ1 FZS1000N Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 123

Yamaha FZ1 FZS1000N Скачать руководство пользователя страница 34

INSTRUMENT AND CONTROL FUNCTIONS

3-13

3

Compression damping force

To increase the compression damping
force and thereby harden the compres-
sion damping, turn the adjusting screw
on each fork leg in direction

a

. To de-

crease the compression damping force
and thereby soften the compression
damping, turn the adjusting screw on
each fork leg in direction

b

.

CI-02E

EC000015

CAUTION:

_

Never attempt to turn an adjusting
mechanism beyond the maximum
or minimum settings.

_

NOTE:

_

Although the total number of clicks of a
damping force adjusting mechanism
may not exactly match the above spec-
ifications due to small differences in
production, the actual number of clicks
always represents the entire adjusting
range. To obtain a precise adjustment,
it would be advisable to check the num-
ber of clicks of each damping force ad-
justing mechanism and to modify the
specifications as necessary.

_

EAU01699

Adjusting the shock absorber
assembly

This shock absorber assembly is
equipped with a spring preload adjust-
ing ring, a rebound damping force ad-
justing knob and a compression
damping force adjusting screw.

EC000015

CAUTION:

_

Never attempt to turn an adjusting
mechanism beyond the maximum
or minimum settings.

_

1. Compression damping force adjusting screw

Minimum (soft)

21 clicks in direction

b

*

Standard

6 clicks in direction

b

*

Maximum (hard)

1 click in direction

b

*

* With the adjusting screw fully turned in direction

a

U5LV10.book Page 13 Wednesday, October 23, 2002 2:45 PM

«
...
32
33
34
35
36
...
»

Содержание FZ1 FZS1000N




























































































































Отзывы:

Нет отзывов