Yamaha FZ1 FZS1000N Скачать руководство пользователя страница 68

Страница: 68 / 123

PERIODIC MAINTENANCE AND MINOR REPAIR

6-17

EAU03958

To change the coolant

1. Place the motorcycle on the cen-

terstand and let the engine cool if
necessary.

2. Remove panel B. (See page 6-9

for panel removal and installation
procedures.)

3. Place a container under the en-

gine to collect the used coolant.

4. Remove the radiator cap.

EW000067

WARNING

Never attempt to remove the radia-
tor cap when the engine is hot.

5. Remove the coolant drain bolt to

drain the cooling system.

6. After the coolant is completely

drained, thoroughly flush the cool-
ing system with clean tap water.

7. Install the coolant drain bolt, and

then tighten it to the specified
torque.

NOTE:

Check the washer for damage and re-
place it if necessary.

1. Coolant drain bolt

1. Radiator cap

Tightening torque:

Coolant drain bolt:

7 Nm (0.7 m·kgf, 5.1 ft·lb)

U5LV10.book Page 17 Wednesday, October 23, 2002 2:45 PM

Содержание FZ1 FZS1000N




























































































































Результаты поиска

Содержание FZ1 FZS1000N

Отзывы:

Yamaha FZ1 FZS1000N, Руководство пользователя, Страница: 68 / 123

Результаты поиска

Содержание FZ1 FZS1000N

Отзывы: