Yamaha FZ1 FZS1000N Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 123

Yamaha FZ1 FZS1000N Скачать руководство пользователя страница 32

INSTRUMENT AND CONTROL FUNCTIONS

3-11

3

EAU04101

Storage compartment

The storage compartment is located
under the seat. (See page 3-10 for seat
removal and installation procedures.)

EWA00005

WARNING

_

●

Do not exceed the load limit of
3 kg (7 lb) for the storage com-
partment.

●

Do not exceed the maximum
load of 189 kg (417 lb) for the
vehicle.

_

When storing the owner’s manual or
other documents in the storage com-
partment, be sure to wrap them in a
plastic bag so that they will not get wet.
When washing the motorcycle, be
careful not to let any water enter the
storage compartment.

EAU04002

Adjusting the front fork

This front fork is equipped with spring
preload adjusting bolts, rebound damp-
ing force adjusting screws and com-
pression damping force adjusting
screws.

EW000035

WARNING

_

Always adjust both fork legs equal-
ly, otherwise poor handling and loss
of stability may result.

_

1. Storage compartment

U5LV10.book Page 11 Wednesday, October 23, 2002 2:45 PM

«
...
30
31
32
33
34
...
»

Содержание FZ1 FZS1000N




























































































































Отзывы:

Нет отзывов