Yamaha FZ1 FZS1000N Скачать руководство пользователя страница 33

Страница: 33 / 123

INSTRUMENT AND CONTROL FUNCTIONS

3-12

Spring preload

To increase the spring preload and
thereby harden the suspension, turn
the adjusting bolt on each fork leg in di-
rection

. To decrease the spring pre-

load and thereby soften the
suspension, turn the adjusting bolt on
each fork leg in direction

NOTE:

Align the appropriate groove on the ad-
justing mechanism with the top of the
front fork cap bolt.

CI-12E

Rebound damping force

To increase the rebound damping
force and thereby harden the rebound
damping, turn the adjusting screw on
each fork leg in direction

. To de-

crease the rebound damping force and
thereby soften the rebound damping,
turn the adjusting screw on each fork
leg in direction

CI-02E

1. Spring preload adjusting bolt

1. Current setting
2. Front fork cap bolt

Setting

Minimum (soft)

Standard

Maximum (hard)

* fully turned out position

1. Rebound damping force adjusting screw

Minimum (soft)

17 clicks in direction

Standard

7 clicks in direction

Maximum (hard)

1 click in direction

* With the adjusting screw fully turned in direction

U5LV10.book Page 12 Wednesday, October 23, 2002 2:45 PM

Содержание FZ1 FZS1000N




























































































































Результаты поиска

Содержание FZ1 FZS1000N

Отзывы:

Yamaha FZ1 FZS1000N, Руководство пользователя, Страница: 33 / 123

Результаты поиска

Содержание FZ1 FZS1000N

Отзывы: