Yamaha FL350A Скачать руководство пользователя | Manualshive

Страница: 83 / 122

background image

Operation

76

TIP:

The engine can also be stopped by pulling
the cord and removing the clip from the en-
gine shut-off switch, then turning the main
switch to “

” (off).

2. If equipped with the Yamaha Security

System: When you leave your boat, set
the Yamaha Security System to the lock
mode by pressing the lock button of the
remote control transmitter. Short beep
will sound once when locking the securi-
ty system. The lock mode is selected
only when the main switch is in the “

”

(off) position. For further information,
see page 24.

WARNING! Do not set

the Yamaha Security System in the
lock mode when you stop the engine
at offshore.

[EWM02150]

3. Remove the key if the boat will be left un-

attended.

ON

OFF

START

ZMU04599

ON

OFF

ZMU07171

OFF

OFF

ON

ON

ZMU05833

OFF

OFF

ON

ON

OFF

ON

ZMU06014

ZMU07148

ZMU07149

6AW-9-77-1E0.book 76 ページ２０１０年３月１６日　火曜日　午後６時８分

«
...
81
82
83
84
85
...
»

Содержание FL350A



























































































































Отзывы:

Нет отзывов

Похожие инструкции для FL350A

Бренд: ASROCK Страницы: 5

B360 GAMING PLUS

Бренд: MSI Страницы: 112

Бренд: Supero Страницы: 86

X570 PHANTOM GAMING 4

Бренд: ASROCK Страницы: 196

Бренд: Gigabyte Страницы: 31

Бренд: Thinklabs Страницы: 129

TPS5420EVM-175 SWIFT

Бренд: Texas Instruments Страницы: 16

Бренд: MSI Страницы: 77

Бренд: Intersil Страницы: 10

Бренд: THORLABS Страницы: 22

Бренд: ECS Страницы: 43

Бренд: Global Страницы: 33

Бренд: SOYO Страницы: 30

UPGRD-KIT-48UXP

Бренд: Advantech Страницы: 2

Бренд: Advantech Страницы: 16

Бренд: Advantech Страницы: 50

Бренд: Advantech Страницы: 92

Бренд: Advantech Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды