Yamaha FL350A Скачать руководство пользователя

Страница: 68 / 122

Operation

When starting the engine using the
Start/Stop button, press the button to
start the engine. The indicator for the
starting engine will come on.

When starting the engine using the
Start/Stop button on the All Start/Stop
panel, press the button to start the all en-
gines.

TIP:

●

When the main switch is turned to “

”

(start) with the clip removed from the en-
gine shut-off switch, the buzzer will sound.

●

Except the single type, if the clip is not in-
stalled to the engine shut off switch, the
buzzer will sound when the Start/Stop but-
ton is pressed.

●

Except the single type, if one of the en-
gines has started, it can be stopped by
pressing the Start/Stop button on the All
start/Stop panel.

EMU42170

Procedure for dual station models (main
station)

1. If equipped with the Yamaha Security

System: If the lock mode of the Yamaha

START

ZMU05830

START

ZMU05994

ZMU07148

ZMU07149

ZMU07150

6AW-9-77-1E0.book 61 ページ２０１０年３月１６日　火曜日　午後６時８分

Содержание FL350A



























































































































Результаты поиска

Содержание FL350A

Отзывы:

Похожие инструкции для FL350A

Бренды по названию

Популярные бренды

Yamaha FL350A, Руководство пользователя

Результаты поиска

Содержание FL350A

Отзывы:

Похожие инструкции для FL350A

Бренды по названию

Популярные бренды