Yamaha F150G Скачать руководство пользователя

Страница: 68 / 104

Operation

EMU42702

Procedure for tilting down

Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

Release the tilt support lever.

Push the power trim and tilt switch “

”

(down) to lower the outboard motor to
the desired position.

EMU28063

Shallow water

EMU40702

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

NOTICE

ECM02361

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

EMU35237

Procedure for power trim and tilt models

Place the control lever in neutral.

1. Tilt support lever

ZMU07770

ZMU05840

ZMU07999

1. Power trim and tilt switch

1. Cooling water inlet

ZMU07771

ZMU07772

U6DV75E0.book Page 61 Tuesday, February 21, 2017 8:33 AM

Содержание F150G









































































































Результаты поиска

Содержание F150G

Отзывы:

Похожие инструкции для F150G

Бренды по названию

Популярные бренды

Yamaha F150G, Руководство пользователя

Результаты поиска

Содержание F150G

Отзывы:

Похожие инструкции для F150G

Бренды по названию

Популярные бренды