Yamaha F150G Скачать руководство пользователя страница 18

Страница: 18 / 104

Specifications and requirements

Gear ratio:

1.86 (26/14) (F175CET, F200GET,
FL175CET, FL200GET)
2.0 (28/14) (F150GET, FL150GET)

Trim and tilt system:

Power trim and tilt

Propeller mark:

M/T (F150GET, F175CET, F200GET)
ML/TL (FL150GET, FL175CET,
FL200GET)

Fuel and oil:

Recommended fuel:

Premium unleaded gasoline (F200GET,
FL200GET)
Regular unleaded gasoline (F150GET,
F175CET, FL150GET, FL175CET)

Min. pump octane number (PON):

89 (F200GET, FL200GET)

Min. research octane number (RON):

90 (F150GET, F175CET, FL150GET,
FL175CET)
94 (F200GET, FL200GET)

Recommended engine oil:

YAMALUBE 4 or 4-stroke outboard
motor oil

Recommended engine oil grade 1:

SAE 10W-30/10W-40/5W-30
API SE/SF/SG/SH/SJ/SL

Engine oil quantity (without oil filter
replacement):

4.3 L (4.55 US qt, 3.78 Imp.qt)

Engine oil quantity (with oil filter
replacement):

4.5 L (4.76 US qt, 3.96 Imp.qt)

Lubrication system:

Wet sump

Recommended gear oil:

YAMALUBE outboard gear oil or Hypoid
gear oil

Recommended gear oil grade:

SAE 90 API GL-4 / SAE 80W API GL-5 /
SAE 90 API GL-5

Gear oil quantity:

0.980 L (1.036 US qt, 0.862 Imp.qt)

Tightening torque:

Spark plug:

28 N·m (2.86 kgf·m, 20.7 lb·ft)

Propeller nut:

54 N·m (5.51 kgf·m, 39.8 lb·ft)

Engine oil drain bolt:

27 N·m (2.75 kgf·m, 19.9 lb·ft)

Engine oil filter:

18 N·m (1.84 kgf·m, 13.3 lb·ft)

Noise and vibration level:

Operator sound pressure level (ICOMIA
39/94):

80.8 dB(A)

EMU33556

Installation requirements

EMU33565

Boat horsepower rating

WARNING

EWM01561

Overpowering a boat can cause severe in-
stability.

Before installing the outboard motor(s), con-
firm that the total horsepower of your out-
board motor(s) does not exceed the boats
maximum horsepower rating. See the boat’s
capacity plate or contact the manufacturer.

EMU40491

Mounting outboard motor

WARNING

EWM02501



Improper mounting of the outboard mo-
tor could result in hazardous conditions
such as poor handling, loss of control,
or fire hazards.



Because the outboard motor is very
heavy, special equipment and training is
required to mount it safely.

U6DV75E0.book Page 11 Tuesday, February 21, 2017 8:33 AM

Содержание F150G









































































































Результаты поиска

Содержание F150G

Отзывы:

Бренды по названию

Популярные бренды

Yamaha F150G, Руководство пользователя

Результаты поиска

Содержание F150G

Отзывы:

Бренды по названию

Популярные бренды