Yamaha F150G Скачать руководство пользователя | Manualshive

Страница: 59 / 104

background image

Operation

52

EMU27495

Starting engine

WARNING

EWM01601

Before starting the engine, make sure that
the boat is tightly moored and that you can
steer clear of any obstructions. Be sure
there are no swimmers in the water near
you.

EMU41791

Start-up checks

Place the control lever in neutral and turn the
main switch to “

” (on). Make sure that no

alert-indicator comes on. If the buzzer
sounds and the water separator-alert indica-
tor blinks, consult your Yamaha dealer imme-
diately.

EMU41904

Procedure for starting engine

WARNING

EWM01842



Failure to attach the engine shut-off
cord could result in a runaway boat if
operator is ejected. Attach the engine
shut-off cord to a secure place on your
clothing, or your arm or leg while oper-
ating. Do not attach the cord to clothing
that could tear loose. Do not route the
cord where it could become entangled,
preventing it from functioning.



Avoid accidentally pulling the cord dur-
ing normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power, the
boat could slow rapidly. This could cau-
se people and objects in the boat to be
thrown forward.

1.

Place the control lever in neutral.

TIP:

The start-in-gear protection device prevents
the engine from starting except when in neu-
tral.
2.

Attach the engine shut-off cord to a se-
cure place on your clothing, or your arm
or leg. Then install the clip on the other
end of the cord into the engine shut-off
switch.

3.

Turn the main switch to “

” (on) to make

sure that the digital electronic control-
active indicator lights. The engine can
not be started when the digital electronic
control-alert indicator lights.

ZMU05829

N

ZMU07167

U6DV75E0.book Page 52 Tuesday, February 21, 2017 8:33 AM

«
...
57
58
59
60
61
...
»

Содержание F150G









































































































Отзывы:

Нет отзывов

Похожие инструкции для F150G

Бренд: Aaeon Страницы: 122

Бренд: Aaeon Страницы: 52

Бренд: Aaeon Страницы: 99

Бренд: Texas Instruments Страницы: 8

A75A-G35 Series

Бренд: MSI Страницы: 72

Бренд: MACHINIST Страницы: 15

Бренд: Sun Microsystems Страницы: 74

Бренд: DFI Страницы: 104

Бренд: Microchip Technology Страницы: 52

Бренд: Microsemi Страницы: 15

Бренд: Tews Technologies Страницы: 26

Бренд: Gigabyte Страницы: 80

Бренд: ITOX Страницы: 114

Бренд: Analog Devices Страницы: 13

Бренд: Texas Instruments Страницы: 33

GF7100P-M7 - BIOS SETUP

Бренд: Biostar Страницы: 45

Бренд: Texas Instruments Страницы: 18

Бренд: Silicon Laboratories Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды