manualshive.com logo in svg

Yamaha F150G, Руководство пользователя

Поделиться
Скачать
Yamaha F150G Скачать руководство пользователя страница 63

Operation

56

engine speed is increased from the fully
closed position during trolling speed setting
mode. When the throttle is returned to the ful-
ly closed position, the display will show the
trolling speed again. When the engine is
turned off or when the engine speed exceeds
3000 r/min, trolling speed setting mode will
be released.
For details, see the attached operation man-
ual.

TIP:

Trolling is affected by currents and other
operating conditions and may differ from
the actual engine speed.

When warming up a cold engine, the troll-
ing speed cannot be decreased below the
specified engine idle speed.

EMU27822

Stopping engine

Before stopping the engine, first let it cool off
for a few minutes at idle or low speed. Stop-
ping the engine immediately after operating
at high speed is not recommended.

EMU41913

Procedure for stopping engine

1.

The engine can be turned off either by
pressing the Start/Stop button or by
turning the main switch to the “

” (off)

position. After the engine has been
turned off using the Start/Stop button,
turn the main switch to the “

” (off) po-

sition.

ZMU06309

Troll stop

SET

MENU

CANCEL

ZMU07256

ON

OFF

ZMU07171

ZMU07148

U6DV75E0.book  Page 56  Tuesday, February 21, 2017  8:33 AM

Содержание F150G









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды