Yamaha DM 1000, Руководство по обслуживанию

Страница: 108 / 307

DM1000/MB1000/SP1000
108
Judgment standard 1: The EFFECT sounds must
be output.
Judgment standard 2: The output must not include
any noise.
In the same manner, recall and inspect Scenes 2
through 16.
The EFFECT functions for Scenes 2 through 16 work
as follows.
Scenes 2: SYMPHONIC
Scenes 3: HQ PITCH
Scenes 4: DYNAMIC FILTER
Scenes 5: REVERB
Scenes 6: SYMPHONIC
Scenes 7: HQ PITCH
Scenes 8: DYNAMIC FILTER
Scenes 9: REVERB
Scenes 10: SYMPHONIC
Scenes 11: HQ PITCH
Scenes 12: DYNAMIC FILTER
Scenes 13: REVERB
Scenes 14: SYMPHONIC
Scenes 15: HQ PITCH
Scenes 16: DYNAMIC FILTER
7. Writing and Initializing Programs
7-1. Program Version Check Method
Press the DM1000 [SEL] key CH5, CH9, CH6, CH3,
in that order, then press the [STORE] key. This
displays the versions of the main program and the
boot program on the LCD screen.
7-2. Program Writing Method
Write the main program and the boot program with
the following method.
1) Connect the PC and the DM1000 with the USB
cable.
(The YAMAHA USB-MIDI driver must be installed
on the PC and the USB-MIDI driver must be set
to Through = Off.)
2) While holding down the MONITOR [CLEAR] key,
switch on the power for the DM1000 main unit and
continue to hold down this key until “FLASH
UPDATE” is displayed on the screen of the DM1000
main unit. For the MAIN circuit board inspection, it
is adequate to just switch on the power.
3) Start the version upgrade program (VerUp.exe).
4) Press the Browse button and select the main
program (file name dm1k.pgm) and the boot
program (file name boot.pgm) to be written.
5) When you press the Load button, the program
writing is started. Never switch off the power or
disconnect the USB cable while the program is
being written.
6) In order to check that the main program and the
boot program have been written correctly, check
their versions with the method in “7-1. Program
Version Check Method”.
7-3. Method for Initialization with Fader Calibration
While holding down both the FADER MODE
[DISPLAY] key and the [AUX1] key, switch On the
power switch (or within 3 seconds of switching On
the power switch, simultaneously press both the
FADER MODE [DISPLAY] key and the [AUX1] key)
to start up the system, then operate according to
the following instructions.
Continue holding down these keys until the Loading
Factory Presets message is displayed on the
DM1000 main unit screen.
After the initialization is complete, check that the DIO
WORD SELECT screen is displayed.
7-4. Method for Initializing without Fader Calibration
While holding down both the AUX SELECT
[DISPLAY] key and the [AUX8] key, switch On the
power switch (or within 3 seconds of switching On
the power switch, simultaneously press both the
FADER MODE [DISPLAY] key and the [AUX8] key)
to start up the system. Check that the DIO WORD
CLOCK SELECT screen is displayed.
Continue holding down these keys until the Loading
Factory Presets message is displayed on the
DM1000 main unit screen.
Loading Factory Presets
Calibrating the Touch Sense..
Do Not Touch the Faders!
Calibrating the Faders...
Do Not Touch the Faders!
Adjust CH1-16 -INFINITY
STEREO -INFINITY
Hit ENTER key
Adjust CH1-16 -15dB
STEREO -30dB
Hit ENTER key
Adjust CH1-16 0dB
STEREO Any Position
Hit ENTER key
Adjust CH1-16 +10dB
STEREO 0dB
Hit ENTER key
Screen message Operation contents
Start of calibration
Do not touch any faders during
Touch Sense calibration and do not
obstruct movement of the faders.
Do not touch any faders during
Fader calibration and do not
obstruct movement of the faders.
Set the CH1~16, STEREO Fader
to -
∞
, then press the [ENTER]
switch.
Set the CH 1~16 Fader to -15dB
and the STEREO Fader to -30dB,
then press the [ENTER] switch.
Set the CH 1~16 Fader to 0dB.
There is no particular need to operate the
STEREO Fader. When this setting is
complete, press the [ENTER] switch.
Set the CH 1~16 Fader to 10 dB
and the STEREO Fader to 0 dB,
then press the [ENTER] switch.