Yamaha 2008 YZF-R1X Скачать руководство пользователя

Страница: 91 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-42

NOTE:

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

5. Install the brake hose holders by

installing the bolts and nuts.

6. Secure the wheel axle by installing

the axle bolt, and then tightening
the axle bolt to the specified
torque.

NOTE:

While tightening the axle bolt, hold the
wheel axle with a 19-mm hexagon
wrench to keep it from turning.

7. Tighten wheel axle pinch bolt B,

and then tighten pinch bolt A to the
specified torque.

8. Retighten pinch bolt B to the spec-

ified torque.

9. Tap the outer side of the right fork

leg with a rubber mallet to align it
with the end of the wheel axle.

10. Tighten wheel axle pinch bolt D,

and then tighten pinch bolt C to the
specified torque.

11. Retighten pinch bolt D to the spec-

ified torque.

12. While applying the front brake,

push down hard on the handlebar
several times to check for proper
fork operation.

Tightening torque:

Brake caliper bolt:

35 Nm (3.5 m·kgf, 25 ft·lbf)

Tightening torque:

Axle bolt:

91 Nm (9.1 m·kgf, 66 ft·lbf)

1. Front wheel axle pinch bolt A
2. Front wheel axle pinch bolt B

3. Front wheel axle pinch bolt C

4. Front wheel axle pinch bolt D

Tightening torque:

Wheel axle pinch bolt:

21 Nm (2.1 m·kgf, 15 ft·lbf)

Tightening torque:

Wheel axle pinch bolt:

21 Nm (2.1 m·kgf, 15 ft·lbf)

U4C821E0.book Page 42 Tuesday, July 17, 2007 11:37 AM

Содержание 2008 YZF-R1X













































































































Результаты поиска

Содержание 2008 YZF-R1X

Отзывы:

Похожие инструкции для 2008 YZF-R1X

Бренды по названию

Популярные бренды

Yamaha 2008 YZF-R1X, Руководство пользователя

Результаты поиска

Содержание 2008 YZF-R1X

Отзывы:

Похожие инструкции для 2008 YZF-R1X

Бренды по названию

Популярные бренды