Yamaha 2008 YZF-R1X Скачать руководство пользователя

Страница: 90 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-41

EAU24360

Front wheel

EAU33921

To remove the front wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the wheel axle pinch bolts,

the axle bolt, and then the brake
caliper bolts.

2. Lift the front wheel off the ground

according to the procedure on
page 6-40.

3. Remove the brake hose holder on

each side by removing the bolt and
nut.

4. Remove the brake caliper on each

side by removing the bolts.

5. Remove the axle bolt, push the

wheel axle out from the left side,
and then remove the wheel.

CAUTION:

ECA11050

Do not apply the brake after the
brake calipers have been removed,
otherwise the brake pads will be
forced shut.

EAU33932

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Lower the front wheel so that it is

on the ground.

4. Install the brake calipers by install-

ing the bolts, and then tightening
them to the specified torque.

1. Front wheel axle pinch bolt

1. Brake hose holder
2. Bolt and nut

3. Brake caliper bolt

4. Brake caliper
5. Axle bolt

1. Wheel axle

U4C821E0.book Page 41 Tuesday, July 17, 2007 11:37 AM

Содержание 2008 YZF-R1X













































































































Результаты поиска

Содержание 2008 YZF-R1X

Отзывы:

Похожие инструкции для 2008 YZF-R1X

Бренды по названию

Популярные бренды

Yamaha 2008 YZF-R1X, Руководство пользователя

Результаты поиска

Содержание 2008 YZF-R1X

Отзывы:

Похожие инструкции для 2008 YZF-R1X

Бренды по названию

Популярные бренды