manualshive.com logo in svg

XYZ Machine Tools SMX 2500, Инструкция по безопасности, установке, обслуживанию, эксплуатации и списку запасных частей

Поделиться
Скачать
XYZ Machine Tools SMX 2500 Скачать руководство пользователя страница 54

50 

XYZ Machine Tools Ltd 

XYZ Bed Mill Safety, Installation, Maintenance, Service & Parts List  Manual

 

 

1st 10 LEDs 

1.

 

Gear 1 – this light should be on whenever the machine is in low gear.  LEDs labelled Gear 2 thru 
Gear 4 are not used. 

2.

 

SPD-FAULT – this light will be on whenever the AC drive is in a fault condition, which includes an 
Emergency-stop message from the pendant. 

3.

 

SPD-RUN – this light should be on whenever the spindle is running 

4.

 

LED labelled SPD-ENABLE – this light should be on whenever you are in DRO, tool setup or RUN 
mode. 

2nd 10 LEDs 

1.

 

E-STOP OUT – this light should be on whenever the Emergency stop is in the out position.  When 

the E-stop is pressed, this light should go off. 

2.

 

LATCH RELAY – this light should be on when the spindle is running or if the spindle is not running 
and the fwd/rev switch is in the off position when in DRO, tool setup or RUN mode.  Note – if 

spindle won’t turn on and the spindle is enabled and the E-stop is out, then either the fwd/rev 
switch is bad or the spindle control module is bad. 

3.

 

TAP MODE – light should be on whenever you are not tapping.  Light will be off when in the tap 
event.  Not applicable to SMX2500. 

4.

 

TAP REVERSE – this light will be on when the spindle changes direction at the bottom of a tap 
event and back off after the spindle changes direction once outside of the tap event. Not 
applicable to SMX2500. 

5.

 

REV-RELAY – when fwd/rev switch is in reverse this light will be on.  Note – this does not mean 
necessarily that the spindle will be running this direction. 

6.

 

FWD-RELAY – when fwd/rev switch is in forward this light will be on.  Note – this does not mean 
necessarily that the spindle will be running this direction. 

7.

 

Z-LIMIT PLUS – this light will be on only when the Z axis plus limit switch is triggered. 

8.

 

Z-LIMIT MINUS – this light will be on only when the Z axis minus limit switch is triggered. 

 

4.7.6

 

Electrical Box – SMX 2500 

The electrical box is made up of the following main components: 

1.

 

Safety Relay – disconnects power during an E-stop condition, 

2.

 

Transformer (415 volt to 110 volt), 

3.

 

Contactors for spindle motor and coolant pump, 

4.

 

Overloads and fuses for protection. 

 

Содержание SMX 2500












































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды