XYZ Machine Tools SMX 2500 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 171

XYZ Machine Tools SMX 2500 Скачать руководство пользователя страница 37

33

XYZ Machine Tools Ltd

XYZ Bed Mill Safety, Installation, Maintenance, Service & Parts List Manual

Do the following Service Codes and procedures:



Code 33 Software Identification. This is needed if you call Customer Service



Code 11 Measures the backlash in the system. Only used on machines with Dual Feedback
systems



Code 12 Feed Forward Constant. High feed forward constants will cause an unstable servo
system



Code 100

Axis open loop test. Used to check the maximum feedrate of an axis and if the

encoders are counting

Possible Cause

Check This

Cable connection problems

Check umbilical 1 and 2. Check #1 for X and Y-axis problems

and #2 for the Z-axis.

X, Y, and Z-axis Gibs are adjusted
extremely tight

Check the adjustment of the X, Y, and Z-axis Gibs using the X,
Y, and Z-axis Gib adjustment procedures. See X, Y, and Z-axis

Gib Adjustments Section 5.2.1

Excessive friction in the slideways

See Machine Tool & Setup Section 4.1

Binding or looseness in the Drive

Train

See Mechanical Drive Train (X, Y) Section 4.2

Incoming electrical power

Incoming voltage. See Electrical Section 4.8

Measurement system not functioning
properly

See Section 4.6 or 4.7

Servo Drive failure

See Servo Driver - Section 4.5

Motor failure

See Motor diagnostics, Section 4.4

Computer/Pendant failure

See Computer/Pendant diagnostics, Section 4.3

3.3.5

Problems Reading the Floppy Disk; Programs Not Saved Properly. The floppy

drive will not read or write programs from a disk.

Possible Cause

Check This

Improper Boot-up

Shut down the system and wait 10 seconds before rebooting

Floppy Disk failure

The Floppy Disk may be bad. See if the Floppy Disk can be read

by a Personal Computer. Does the green light on the floppy

drive come on when you access the disk? If so, power is
getting to the floppy drive. If not check connections of floppy
drive inside the computer module. See Computer/Pendant

Section 4.3 for more information.

Floppy Disk full

Put the Floppy Disk into a Personal Computer to see how many

bytes remain. A floppy can typically hold 1.4 MB of

information.

3.3.6

System Will Not Boot-Up

The system does not boot-up when the switch is turned on.

Possible Cause

Check This

Flash Drive failure

When the Computer Module starts the boot-up process, look at

the 8th line on the Display Screen. If the Mother Board of the
Computer Module is communicating with the Flash Drive you

will see "Detecting IDE Primary Master…Scan Disk SDCFB-256".
If the Mother Board of the Computer Module is not
communicating with the Flash Drive you will see "Detecting IDE

Primary Master … None".

«
...
35
36
37
38
39
...
»

Содержание SMX 2500












































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды