XYZ Machine Tools SMX 2500 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 171

XYZ Machine Tools SMX 2500 Скачать руководство пользователя страница 42

38

XYZ Machine Tools Ltd

XYZ Bed Mill Safety, Installation, Maintenance, Service & Parts List Manual



Code 313 Check the line that specifies the product. If the product does not match the machine
then either the machine ID key is incorrect or else the pendant is faulty.



Code 921 (922): Toggles the direction in which the X (Y) motor drives the table (saddle).



See also Codes 321 and 322, in sections 4.8.2.10 and 4.8.2.11.

3.4.5

X, Y, & Z-Axis Electric Handwheels Turn in Wrong Direction

The Electric Handwheels turn in the wrong direction.
The positive directions for each Electric Handwheel should be:



X-axis - Electric Handwheel turns clockwise



Y-axis - Electric Handwheel turns anti-clockwise

Do the following service code and procedures:



Code 308 Reverse X-axis Handwheel Direction



Code 309 Reverse Y-axis Handwheel Direction

3.5

Problems with the Machine

3.5.1

3.5.1 Z-Axis Noisy

While jogging or cutting in the Z-axis direction, the axis makes unusual noises. See below for head noise.

Possible Cause

Check This

Machine Tool and Setup problem

Check for any looseness in the setup (Tool, Tool holder, Part, Vice,

or Fixture). See Machine Tool & Setup Section 4.1

Inadequate or no Lubrication to

the Ballscrew and Way surfaces

Make sure all the Way surfaces are getting proper lubrication. If

not, check to make sure that the lube pump is functioning
properly. Also check for any pinched or blocked oil lines. See

Lubrication Section 4.1.3

Z-axis Gibs are not adjusted

properly

Check the adjustment of the Z-axis Gibs using the Z-axis Gib

adjustment procedure. See Z-axis Gib Adjustments Section 5.2.1

Mechanical Drive Train

Misalign ballscrew, or top and lower bearing failure.

Z-axis motor failure

Replace Z-axis motor, see Motor Diagnostics Section 4.4

3.5.2

3.5.2 Spindle Stalls or Turns-Off During Machining

During machining, the spindle turns off and loses power. First check incoming voltage and connections.

Possible Cause

Check This

Machine Tool and Setup problem

Check the type of material being cut, type and size of cutting tool,

RPM, and Feed rate. Also check the condition of the cutter to verify

that the cutter is not dull. See Machine Tool & Setup Section 4.1

Drive Belt in the head is slipping

Check the alignment, condition, and tension of the Drive Belt.

Cutting more than the machine is

capable

Check width and depth of cut

Spindle Drive thermal Overload

has tripped

Check AC drive fault history (for SMX2500, check spindle overload

relay in electrical cabinet)

Spindle Drive incorrectly
configured.

Contact Customer Service for assistance.

Spindle run command not

reaching AC Drive

Verify spindle run LED is on Spindle Control Module.

3.5.3

Spindle Motor Hums or Will Not Run

The spindle motor makes a constant humming noise during operation or will not turn on.

«
...
40
41
42
43
44
...
»

Содержание SMX 2500












































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды