manualshive.com logo in svg

XYZ Machine Tools SMX 2500, Инструкция по безопасности, установке, обслуживанию, эксплуатации и списку запасных частей

Поделиться
Скачать
XYZ Machine Tools SMX 2500 Скачать руководство пользователя страница 39

35 

XYZ Machine Tools Ltd 

XYZ Bed Mill Safety, Installation, Maintenance, Service & Parts List  Manual

 

 

Do the following service code and procedures: 

 

Code 33 Software Identification.  This is needed if you call Customer Service. 

 

Code 329 Control Outputs.  Enables the outputs to be turned on/off manually (Press Code F first 
to access codes 328 through to 330) 

 

Possible Cause 

Check This 

Blown fuse 

Check the fuses feeding the coolant pump and also the coolant 
pump control circuit. 

Poor cable connections 

Check all the cable connections on the cable breakout box and 

Coolant Pump.  In particular, check umbilical # 2 cable, which 
carries the auxiliary function signals. 

Bad cable breakout box  

Check for continuity between the following pins when the 
corresponding aux function is activated: 

 

Coolant connector: 

1 and 4 

 

Indexer connector: 

3 and 4 

 

Spindle connector: 

1 and 4 

3.3.11

 

Emergency Stop Error (E-Stop) 

The E-Stop turns the power off to the axis and spindle motors. SMX Bed Mills have an E-stop on the front 

of the pendant and a reset button on the side of the pendant. (See figures 9 & 10).  When the E-stop is 
activated: 

 

Power to the cable break out box (from the pendant AC E-stop Out connector) is isolated via the 
E-stop relay inside the pendant.  This isolates power to the axes motors. 

 

The spindle AC drive power is turned off by a contactor (K1), located on the power module. The 
contactor (K1) is turned off by the dual channel safety relay, which monitors the pendant E-stop. 
(for SMX2500, the safety relay removes 24VAC power to the spindle contactors) 

The E-stop LED on the spindle control module will be on when the e-stop is in the out position. The LED 
will turn off when the E-stop is depressed. (See figure 10). 
If the E-Stop button is depressed, and no message is displayed on the screen, then either the pendant, 
spindle control module, cables from pendant to spindle control module, or cables from spindle control 
module to dual channel relay (safety relay) are at fault. 

 

Possible Cause 

Check This 

E-Stop reset button 

Press the E-Stop reset button on the side of the pendant. 

Bad pendant 

Does 110 V power come out of the AC E-stop Out connector on the 

pendant?  If yes and the screen has an E-stop message then 
replace the pendant. 

Poor cable connection 

Check spindle control cable connection and Euro connector 
connections. 

3.3.12

 

Limit Switch Error 

Limit switches are installed on the table, saddle, and head to prevent serious damage to the machine in 
the event of overtravel.  In the event a limit switch is triggered, a limit switch error will appear on the 
screen. 

 

To return the machine to its normal state of operation, perform the following procedure: 

1.

 

Jog the table, saddle, or head off the switch. 

2.

 

Press the "Mode" or "Return" key to reset the control 

3.

 

Press the "DRO" key to access the Jog function again. 

Содержание SMX 2500












































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды