Xyplex Terminal Server 720 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 102

background image

Introducing the Terminal Server 720

Serial Port I/O and Cabling Options -- There are three serial I/O and cabling schemes
available for the Terminal Server 720.

-

Model 721 16-port I/O module. Two 50-pin TELCO connectors provide six-wire
connections for sixteen serial devices, using a variety of wiring schemes, such as
extension cables, distribution panels. splitters, octopus cables, punch-down blocks,
modular (MODtap™) cabling, and DECconnect™ cabling. These ports support
modem control signals and communication speeds from 75 bps to 115.2 Kbps.

-

Model 723 20-port I/O module. Twenty RJ-45 connectors provide eight-wire
connections for twenty serial devices using modular cabling. These ports support
modem control and concurrent hardware flow control, and communication speeds
from 75 bps to 115.2 Kbps.

-

Model 724 24-port I/O module. Three 50-pin TELCO connectors provide six-wire
connections for twenty-four serial devices, using the same wiring schemes available
for the Model 721 I/O module. These ports support modem control signals and
communication speeds from 75 bps to 115.2 Kbps.

☞

When using port speeds higher than 64 kbps, you must be careful to use a cabling
scheme that minimizes the potential for "cross-talk" problems. Cabling
methods, such as punch-down blocks used in conjunction with bundled 50-wire
cables can suffer from cross-talk at these data rates. It is recommended that you
use separate shielded cables for each port (for example, a Xyplex octopus cable),
when using the TELCO I/O modules, or short cable lengths.

Network Software Loading -- If you order a server without a memory card, the unit loads its
operating software from a network host called a load server. The load server is typically a
UNIX

TM

or VAX/VMS

TM

system, a Xyplex loader (a MAXman unit, for example), or a Network

9000 product equipped with a memory card. The load server downloads a software image to the
server, over the network, whenever the server is powered on or re-initialized. The load server
can support other types of Xyplex devices as well.

0021

1-9

«
...
5
6
7
8
9
...
»

Содержание Terminal Server 720







































































































Отзывы:

Нет отзывов

Похожие инструкции для Terminal Server 720

Бренд: Panasonic Страницы: 28

6219 - IntelliStation M - Pro

Бренд: IBM Страницы: 317

x3655 - System - 7985

Бренд: IBM Страницы: 118

Бренд: Ganz Страницы: 5

WECS II 2048/DMX/02

Бренд: Oase Страницы: 67

SUPERSERVER 6035B-8R+

Бренд: Supero Страницы: 110

HP ProLiant DL360P Gen8

Бренд: Honeywell Страницы: 67

SUPERSERVER 5028TK-HTR

Бренд: Supermicro Страницы: 138

Бренд: Artesyn Embedded Technology Страницы: 2

Бренд: Axis Страницы: 168

Бренд: Axis Страницы: 10

Бренд: Kathrein Страницы: 16

Бренд: Kathrein Страницы: 16

Бренд: Kathrein Страницы: 16

Бренд: GIGA-BYTE TECHNOLOGY Страницы: 90

Бренд: Lantronix Страницы: 424

SafeNet ProtectServer Network HSM 5.9

Бренд: Thales Страницы: 37

Бренд: Inspur Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды