Xylem YSI IDS ProOBOD Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 13

Xylem YSI IDS ProOBOD Скачать руководство пользователя страница 2

Item #626471
Rev C
Drawing # A626471
April 2013

©2013 YSI Incorporated.

The YSI, ProODO, OBOD and ODO logos are registered trademarks of
YSI Incorporated.

C O N T E N T S

Warranty ................................................................................................ i

Introduction .........................................................................................1

Getting Started ....................................................................................2

Unpacking the OBOD Probe ................................................3

OBOD Probe Operation .....................................................................4

Powering the Stirrer ...............................................................4
Calibration - Dissolved Oxygen ............................................4
Temperature ...........................................................................5
Taking Measurements ............................................................5

Maintenance and Storage ..................................................................5

Updating Instrument and Probe Firmware ..........................6
Sensor Maintenance - Dissolved Oxygen ............................6
Sensor Maintenance - Temperature .....................................8
Sensor Storage .......................................................................9

Troubleshooting ..................................................................................9

Dissolved Oxygen Readings .................................................9
Error/Status messages ........................................................11

Probe Specifications ..........................................................................11

Accessories / Parts List ......................................................................12

Declaration of Conformity ................................................................13

Recycling ............................................................................................14

Contact Information ..........................................................................14

Ordering and Technical Support ........................................14
Service Information ..............................................................15

Appendix A - DO% Calibration Values ............................................16

«
1
2
3
4
...
»

Содержание YSI IDS ProOBOD














Отзывы:

Нет отзывов