Xylem Lowara Q-smart, Инструкция по установке, эксплуатации и обслуживанию

Страница: 41 / 412

en - Original instructions
41
c04 Sensor sig-
nal type 1= 4-20mA
2= 0-20mA - 1
c05 Initial scale
value of the
sensor. Only
if sensor is
used. Pressure:
0 to 60 bar
Tempera-
ture:
-20 to 100°C
Level:
0 to 50 m vari-
ous 0
r05 Calibration
of the initial
scale in mA. 0= Disabled
1= Enabled - 0
t05 Software
filter for ana-
logue input Standard
Lowara - 3
c06 Full scale
value of the
selected
sensor. Only
if sensor is
used. Pressure:
0 to 60 bar
Tempera-
ture:
-20 to 100°C
Level:
0 to 50 m Vari-
ous 10.0
THRESHOLD AND TIMING (threshold is active
only with sensor)
c07 Unique level
set point 0= Disabled
1= Enabled - 0
r07 Set point
level value 0 to Full
Scale Vari-
ous 5
r08 Upper
threshold
delta 0 to Full
Scale Vari-
ous 0.5
r09 Lower
threshold
delta 0 to Full
Scale Vari-
ous 0.5
r10 Threshold
Start Pump 1 0 to Full
Scale Vari-
ous 8
t10 Delay time
start Pump 1 0 to 100 sec 2
r11 Threshold
Stop Pump 1 0 to Full
Scale Vari-
ous 2
t11 Delay time
stop Pump 1 0 to 100 sec 0
r12 Threshold
Start Pump 2 0 to Full
Scale Vari-
ous 7
t12 Delay time
start Pump 2 0 to 100 sec 2
r13 Threshold
Stop Pump 2 0 to Full
Scale Vari-
ous 1
t13 Delay time
stop Pump 2 0 to 100 sec 0
COMBINATION (refer to section 6.2 for descrip-
tion)
c14 Enable
combina-
tions of
stopping
and/or start-
ing the
pumps by
the float 0= only G1
and G2
1= only G
MIN and S
MIN con-
nected (float
switch or
probe S MIN - 3
switches (G)
and probes
(S).
+ common S
COM probe)
2= only G
MAX and S
MAX con-
nected (float
switch or
probe S
MAX +
common S
COM probe)
3= G MIN/S
MIN and G
MAX /S
MAX
STARTING PUMP ROTATION
c15 Enable
pump rota-
tion. Auto-
matic pump
rotation
takes place
each time
the set is
restarted
after stop-
ping in au-
tomatic
mode. If
cyclic ex-
change of
the pumps is
disabled, the
floats or
probes must
be connect-
ed to their
relative
pumps: P1-
G1 (or S1),
P2-G2 (or
S2).
This function
is essential
when the
pumps are
located at
different
stations. 0= Disabled
1= Enabled - 1
c16 Insert the
duty pump
that you
want to start
first after
powering up
or after re-
set.
Parameter
c15 must be
in ENA-
BLED mode 1= Pump 1
2= Pump 2 - 1
c17 If automatic
pump rota- 0= Disabled
1 to 12 Hour
s 0