Xylem GOULDS LB Скачать руководство пользователя страница 3

Страница: 3 / 24

1.3

Motors must be wired for proper voltage. Motor wir-

ing diagram is on motor nameplate. Wire size must
limit maximum voltage drop to 10% of nameplate
voltage at motor terminals, or motor life and pump
performance will be lowered.

1.4

Always use horsepower-rated switches, contactor and

starters.

1.5

Motor protection

1.5.1

Single-phase: Thermal protection for single-

phase units is sometimes built in (check name-
plate). If no built-in protection is provided, use
a contactor with a proper overload. Fusing is
permissible.

1.5.2

Three-phase: Provide three-leg protection with

properly sized magnetic starter and thermal
overloads.

1.6

Maximum Operating Limits:

Liquid Temperature:

140ºF (60ºC)

Working Pressure:

85 PSI

Starts per Hour:

20, evenly distributed.

1.7

Regular inspection and maintenance will increase

service life. Base schedule on operating time. Refer
to Section 8.

2. INSTALLATION

2.1

Locate pump as near liquid source as possible (below

level of liquid for automatic operation).

2.2

Protect from freezing or ﬂooding.

2.3

Allow adequate space for servicing and ventilation.

2.4

All piping must be supported independently of the

pump, and must “line-up” naturally.

NEVER DRAW PIPING IN PLACE BY
FORCING THE PUMP SUCTION AND

DISCHARGE CONNECTIONS.

2.5

Avoid unnecessary ﬁttings. Select sizes to keep fric-

tion losses to a minimum.

2.6

Units may be installed horizontally, inclined or verti-

cally.

DO NOT INSTALL WITH MOTOR
BELOW PUMP. ANY LEAKAGE OR

CONDENSATION WILL AFFECT THE MOTOR.

2.7

Foundation must be ﬂat and substantial to eliminate

strain when tightening bolts. Use rubber mounts to
minimize noise and vibration.

2.8

Tighten motor hold-down bolts before connecting

piping to pump.

3. SUCTION PIPING

3.1

Low static suction lift and short, direct, suction pip-

ing is desired. Consult pump performance curve for

Net Positive Suction Head Required.

SAFETY INSTRUCTIONS

TO AVOID SERIOUS OR FATAL PERSONAL
INJURY OR MAJOR PROPERTY DAMAGE, READ
AND FOLLOW ALL SAFETY INSTRUCTIONS IN
MANUAL AND ON PUMP.

THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT
AND MUST BE KEPT WITH THE PUMP.

This is a

SAFETY ALERT SYMBOL

When you see this symbol on the pump
or in the manual, look for one of the
following signal words and be alert
to the potential for personal injury or
property damage.
Warns of hazards that

WILL

cause

serious personal injury, death or major
property damage.
Warns of hazards that

CAN

cause

serious personal injury, death or major
property damage.
Warns of hazards that

CAN

cause per-

sonal injury or property damage.

NOTICE: INDICATES SPECIAL INSTRUCTIONS

WHICH ARE VERY IMPORTANT AND
MUST BE FOLLOWED.

THOROUGHLY REVIEW ALL INSTRUCTIONS
AND WARNINGS PRIOR TO PERFORMING ANY
WORK ON THIS PUMP.
MAINTAIN ALL SAFETY DECALS.

UNIT NOT DESIGNED FOR USE
WITH HAZARDOUS LIQUIDS OR
FLAMMABLE GASES. THESE
FLUIDS MAY BE PRESENT IN
CONTAINMENT AREAS.

DESCRIPTION and SPECIFICATIONS:

The Model LB is a single stage, centrifugal jet pump for
general liquid transfer service and booster applications.
The liquid end utilizes a 304SS stamped casing, Noryl®
impeller, Lexan® ejector and guidevane, Amodel®
motor adapter and EPR o-rings. All motors are NEMA
48Y and 56Y square ﬂange with a 304SS threaded shaft
extension.

1. IMPORTANT

1.1

Inspect unit for damage. Report any damage to car-

rier/dealer immediately.

1.2

Electrical supply must be a separate branch circuit

with fuses or circuit breakers, wire sizes, etc., in
compliance with National and Local electrical codes.
Install an all-leg disconnect switch near pump.

ALWAYS DISCONNECT ELECTRICAL
POWER WHEN HANDLING PUMP OR

CONTROLS.

DANGER

WARNING

CAUTION

WARNING

Hazardous ﬂuids can
cause ﬁre, burns
or death.