Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 29

Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 9

9

Step 3 – Mounting the receiver

No matter which XtremeLink

®

receiver you use, the mounting procedure is

the same.  The most important thing to remember is that you must keep the
antenna  portion  of  receiver  no  less  than  2  inches  from  any  type  of  large
metal or wiring that is not directly coming out of the receiver.  This includes
steel,  carbon  fiber,  servos,  fuel  pumps,  any  type  of  wiring,  etc.    The  best
method of mounting is to show it off!  Mount the receiver as high and out in
the  open  as  possible  so  you  can  easily  see  it  and  get  access  to  it  (see
Figures 5 & 6 for examples).  Under no circumstance can you wrap or pass
servo wires around the antenna!

Remember that wires can move under

g-force, so make sure that wires can not move

at all

around the

receiver.

Moving wires can cause intermittent radio control.

See

figures 5 and 6 for reference.

We have found the best receiver orientation to be with the antenna pointing
upwards, which gives the best results when making approaches from far
away.

Figure 5 – XtremeLink

®

8 channel receiver installation

«
...
7
8
9
10
11
...
»

Содержание XtremeLink






























Отзывы:

Нет отзывов