Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 29

Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 24

24

Follow the instructions of above. The range test will be limited to
approximately 35 feet instead of at least 125 feet for full range receivers.

WARNING! DO NOT PRESS AND HOLD THE PROG BUTTON DURING
THE NORMAL OPERATION (FLYING, DRIVING, ETC.) OF YOUR R/C
DEVICE!

Setting the Failsafe

If no failsafe is programmed, the servos will hold their last known valid state
when a failsafe condition occurs.  The default failsafe time is 2 seconds.

You can program the failsafe condition for each channel as described above.
Once  you  have  set  the  failsafe  map  conditions,  you  can  then  set  the  user
defined channels.  To do this, turn on the XtremeLink

®

system so that servos

can be moved. Now, press and hold the programming button on the
XtremeLink

®

receiver until the STATUS LED goes out, and release the

button.    The  STATUS  LED  will  begin  alternately  flashing  red  and  green  for
about  8  seconds.    During  this  time,  move  your  sticks  and  switches  to  the
where  you  would  like  them  during  a  failsafe  condition.    NOTE  -  Only  those
channels  programmed  in  the  failsafe  map  will  change  to  a  user  defined
position.    All  other  channels  will  hold  their  last  positions  when  a  failsafe
occurs.

Servo Outputs

The  8  and  10  channel  receivers  do  not  have  markings  for  the  servo
connector  polarity.    The  servos  and  any  battery  connections  can  be  safely
plugged in either way, however, the receiver and servos will only work if the
proper polarity is used.  See Figure 8 for the servo output diagram.

WARNING!

PLUGGING A BATTERY INTO THE PORT LABELED ‘B/T’ WITH THE
POLARITY

REVERSED

WILL

RESULT

IN

UNPREDICTABLE

OPERATION!    THE  RECEIVER  WILL  POWER  UP,  BUT  SERVO
CONTROLS  WILL  NOT  FUNCTION  PROPERLY.    TWITCHING  SERVOS,
BLINKING  RECEIVER  LED  AND  OTHER  ODDITIES  WILL  BE  SEEN.
RANGE WILL BE UNUSABLE, EVEN IF A RANGE CHECK SHOWS RANGE
TO BE NORMAL.

«
...
22
23
24
25
26
...
»

Содержание XtremeLink






























Отзывы:

Нет отзывов