Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 29

Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 18

18

Below is a table of allowable settings:

Country

Setting

All Countries except France

1

France

2

FUNCTION 3 - SET OUTPUT MODE

Range: N/A

This function is not currently supported.

The STATUS LED will be solid

orange. It will be supported in future versions for a new function.

FUNCTION 4 - SET FAILSAFE MAP

Range: 1 to number of receiver channels

It is possible to set the failsafe control for each channel output individually.
You  can  set  each  channel  to  either  hold  last  position,  or  to  use  the  user
defined position (discussed in section 4).  NOTE - The default for ALL outputs
is hold last position.

With the STATUS LED blinking red, press and hold the programming button
until the STATUS LED turns off.  The STATUS LED will now flash orange the
number  of  times  equal  to  the  current  channel  output,  followed  by  a  one
second pause.  When you first enter the failsafe map programming (channel
1), the STATUS LED will flash once, followed by a one second pause.

«
...
16
17
18
19
20
...
»

Содержание XtremeLink






























Отзывы:

Нет отзывов