Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 29

Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 28

28

Keep Your Setups Simple

Although modelers love to have the latest and greatest toys, there are some
products that can introduce new potential failure points when installed.  For
this reason, we recommend that you keep your setups as simple as possible.
Instead  of  using  “power  expansion”  type  devices,  we  recommend  using
power  inputs  to  both  ends  of  the  XtremeLink

®

receiver’s servo connection

bus. For example, when using an XtremeLink

®

10 channel receiver, power

should  be  connected  to  the  B/T  port  and  channel  10  (even  if  a  Y-cable  is
required).  Using two separate flight packs on each end of the servo bus will
give  you  double  the  current  capacity  and  a  functioning  system  if  one  pack
were to fail.

PLEASE  NOTE  THAT  THE  6  CHANNEL  PARK  FLYER  RECEIVERS
DO NOT HAVE A LOW VOLTAGE WARNING INDICATOR, SO THE
STATUS  LED  WILL  NEVER  TURN  SOLID  ORANGE  UNDER  A  LOW
VOLTAGE  CONDITION!    PLEASE  LOAD  TEST  THESE  SETUPS  TO
DETERMINE PROPER VOLTAGE!

«
...
26
27
28
29
»

Содержание XtremeLink






























Отзывы:

Нет отзывов