Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 29

Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 19

19

Every  time  you  press  and  release  the  programming  button,  the  channel
position will advance by one.  The failsafe map position begins at channel 1
(one  flash)  and  ends  with  the  number  of  channels  that  your  receiver  has.
So,  the  8  channel  XtremeLink

®

has eight possible channel output positions,

while the 10 channel XtremeLink

®

receiver has ten possible channel output

positions.

To  change  the  failsafe  control  for  that  channel  output,  press  and  hold  the
programming  button  until  the  STATUS  LED  turns  off  and  begins  to  flash
green.  The STATUS LED will flash either one time (failsafe hold) or flash two
times (failsafe is user defined). After the STATUS LED is done flashing green,
you have five seconds to enter a new failsafe control value.  You do this by
pressing  and  releasing  the  programming  button  either  one  time  for

hold

last position

or two times for

user defined position

.

If  you  do  not  press  the  programming  button  within  five  seconds,  or  if  the
value  you  enter  exceeds  what  is  allowed,  the  STATUS  LED  will  alternately
flash red and green (error condition occurred) and no change will be made.
At  this  point,  you  are  back  at  the  failsafe  map  position  where  you  can
advance  to  the  next  channel.    There  is  no  way  to  get  back  to  the
programming  mode  start  with  this  feature  other  than  by  powering  off  the
receiver and re-entering the advanced programming mode.

If  you  do  make  a  change,  the  STATUS  LED  will  blink  green/red/orange  in
rapid succession to let you know that the change was successful.

If you wanted a low throttle condition and all other outputs to hold their last
position  with  a  JR  radio  setup,  you  would  set  the  failsafe  map  so  that
channel 1 was two flashes (failsafe is user defined), and all other outputs to
one  flash  (hold  position).    You  would  then  need  to  set  the  failsafe  as
described in section 4 to obtain your low throttle position.

FUNCTION 5 - SET FAILSAFE TIME

Range: 1 to 5 seconds

A failsafe condition occurs when data received by the XtremeLink

®

receiver is

not valid for some period of time. This time can be set from one to five
seconds.

«
...
17
18
19
20
21
...
»

Содержание XtremeLink






























Отзывы:

Нет отзывов