Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 29

Xtreme Power Systems XtremeLink Скачать руководство пользователя страница 17

17

If  you  do  not  press  the  programming  button  within  five  seconds,  or  if  the
value  you  enter  exceeds  what  is  allowed,  the  STATUS  LED  will  alternately
flash red and green (error condition occurred) and no change will be made.
At  this  point,  you  are  back  at  the  channel  map  position  where  you  can
advance  to  the  next  channel.    There  is  no  way  to  get  back  to  the
programming  mode  start  with  this  feature  other  than  by  powering  off  the
receiver and re-entering the advanced programming mode.

If  you  do  make  a  change,  the  STATUS  LED  will  blink  green/red/orange  in
rapid succession to let you know that the change was successful.

FUNCTION 2 - SET COUNTRY

Range: 1 to 4

With  the  STATUS  LED  solid  green,  press  and  hold  the  programming  button
until the STATUS LED turns off.  The LED STATUS will now slowly flash green
the number of times equal to the current country setting.  For example, the
default country level is 1, so the STATUS LED will flash just once.

After  the  flashing  stops  you  have  five  seconds  to  change  the  country.    To
change the country, press and release the programming button the number
of times necessary to equal the country from the list below. For example, if
you  wanted  to  set  the  country  to  France,  you  would  press  and  release  the
programming button two times.

If  you  do  not  press  the  programming  button  within  five  seconds,  or  if  the
value  you  enter  exceeds  what  is  allowed,  the  STATUS  LED  will  alternately
flash red and green (error condition occurred) and no change will be made.
At  this  point,  you  are  back  at  the  programming  mode  start  where  you  can
select another programming option.

If  you  do  make  a  change,  the  STATUS  LED  will  blink  green/red/orange  in
rapid succession to let you know that the change was successful.

The country selection is necessary to meet various FCC, ETSI, IC, and other
guidelines.

NOTE:  This  setting  only  applies  to  Hopping  Mode  1,  and  is  ignored  for  all
other hopping modes.

«
...
15
16
17
18
19
...
»

Содержание XtremeLink






























Отзывы:

Нет отзывов