XS Scuba SEAAIR Скачать руководство пользователя

Страница: 29 / 31

Service & Repair Manual

1. Excessive intermediate pressure.

1. Refer to first stage troubleshooting

2. Damaged or worn LP seat.

2. Replace with new.

3. Damaged orifice sealing surface.

3. Replace with new.

4. Damaged orifice O-ring.

4. Replace with new.

5. Orifice incorrectly adjusted.

5. Reset to preliminary setting and

readjust.

6. Poppet spring damaged.

6. Replace with new.

7. Lever pad is damaged or incorrectly

7. Replace with new.

installed.

1. Insufficent intermediate pressure.

1. Refer to first stage troubleshooting

2. Orifice incorrectly adjusted.

3. Reset to preliminary setting and

readjust.

3. Lever is damaged.

3. Replace with new.

1. Lever is slack, or orifice incorrectly adjusted. 1. Reset to preliminary settings and

readjust.

2. Lever is bent.

2. Replace with new.

1. Exhaust valve worn or damaged.

1. Replace with new.

2. Mouthpiece worn or damaged.

2. Replace with new.

3. Adjustment knob or O-ring damaged,

3. Disassemble and inspect, replace or

incorrectly installed, or worn.

reassemble as required.

Symptom

poSSible CauSe

treatment

Freeflow or leakage

(Adjustment knob turned in)

Excessive Inhalation Resistance

or Hesitation

(Adjustment knob turned out)

Insufficient airflow when

purge button is depressed

Troubleshooting Guide

Second Stage

Water entering second stage

Содержание SEAAIR
































Результаты поиска

Содержание SEAAIR

Отзывы:

Похожие инструкции для SEAAIR

Бренды по названию

Популярные бренды

XS Scuba SEAAIR, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание SEAAIR

Отзывы:

Похожие инструкции для SEAAIR

Бренды по названию

Популярные бренды