XINKE A400 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 25

XINKE A400 Скачать руководство пользователя страница 16

14

02/99

Stoppin Max :
Time limit for closure of fuel solenoid to reach genset shut down conditions.

Alarm On Max :
Delay of R#3 relay activation (external audible alarm).

LubPump On :
Operating time of pre-lubricating pump.

LubPump Off :
Delay between 2 operations of the pre-lubricating pump..

LoadBreak >> Make :
ATS delay.

Contactor Delay :
Delay assigned to contactor between time of closure and return of information on Progress.

K # 7 On >> K # 8 On :
Use in configuration #3. Delay of closure which exists between commands K#7 and K#8 (outputs IOB1).

kW Quota ++ :
When Progress is in configuration #4 (mains paralleling) and In#16 not activated; time before the export quota in kW
increases.

kW Quota -- :
When Progress is in configuration #4 (mains paralleling) and In#16 not activated; time before the export quota in kW
decreases.

kVAr Quota ++ :
When Progress is in configuration #4 (mains paralleling) and In#16 not activated; time before the export quota in kVAr
increases.

kVAr Quota -- :
When Progress is in configuration #4 (mains paralleling) and In#16 not activated; time before the export quota in kVAr
decreases.

R # 1 Off >> On :
When option R#1 : Trip\kW Load is at 1, it is the time before relay #1 is excited.
R # 1 On >> Off :
When option R#1 : Trip\kW Load is at 1, it is the time before relay #1 is de-excited.
Parll Start :
When option Parall Auto Start is at 1, it is the delay assigned to the genset before its start-up on a load increase.

Parll Stop :
When option Parall Auto Start is at 1, it is the delay assigned to the genset before its shutdown on a load decrease.

LS Settling :
When option Parall Auto Start is at 1, it is the delay for 2 gensets to shut down after a significant decrease of load.

B - SET POINTS

User Password :
The user must enter a 4-digit password to change the operating mode or to change parameters.

Cranking Attempts :
Number of start-up attemps.

Overspeed RPM :
Overspeed threshold depending on the engine rating.

CrankStop RPM :
Threshold of starter throw out depending on the type of starter used.

Bat OvVoltage :
Threshold of battery overvoltage authorised.

Bat UnVoltage :
Threshold of battery undervoltage authorised.

GEN OvVoltage :
Threshold of overvoltage applied to phase/neutral voltage.

Http://www.xinke-hk.com

ShenZhen XinKe power equipment Co .Ltd

«
...
14
15
16
17
18
...
»

Содержание A400


























Отзывы:

Нет отзывов