Xilinx Virtex-II Pro Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 30

Xilinx Virtex-II Pro Скачать руководство пользователя страница 16

16

www.xilinx.com

Virtex-II Pro Prototype Platform User Guide

1-800-255-7778

UG027 / PN 0402044 (v1.6) October 25, 2002

Chapter 1: Virtex-II Pro Prototype Platform

R

3. Configuration Ports

These headers can be used to connect a Parallel Cable III or Parallel Cable IV cable to the
board and support all Virtex-II Pro device configuration modes. (See

Table 1-3

for

connecting the cables to the Configuration Ports.)

4. JTAG Termination Jumper

The JTAG termination jumper is used to short the TDI pin of the downstream System ACE
connector to the TDO pin of the upstream System ACE connector for the final board in a
chain.

TCK and TMS are parallel feedthrough connections from the upstream System ACE
connector to the downstream System ACE connector and drive the TCK and TMS pins of
the onboard PROMs and the DUT.

Note:

The termination jumper must be in place on the last board in the chain to connect the TDO

pin of the final device to the TDO feedback chain.

Figure 1-3

shows the setup of the JTAG chain on the board.

Table 1-2:

Slave Serial Mode

Configuration Port Header

Parallel Cable III/IV Pins

VCC3

VCC

GND

GND

CCLK

CCLK

DONE

D/P

D0

DIN

PROG

PROG

INIT

Figure 1-3:

JTAG Chain Termination

UG027_03_030102

PROM1

TDO

TDI

TDO

TDO

TDI

PROM2

UP

DN

DUT

TDI

TMS

TDI

TCK

TDO

TCK

TMS

TDO

«
...
14
15
16
17
18
...
»

Содержание Virtex-II Pro































Отзывы:

Нет отзывов