Xilinx Virtex-5 RocketIO GTP Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 316

background image

Virtex-5 RocketIO GTP Transceiver User Guide

33

UG196 (v1.3) May 25, 2007

Ports and Attributes

R

CLK_COR_MIN_LAT_0

CLK_COR_MIN_LAT_1

Specifies the minimum elastic buffer latency.

Configurable Clock Correction

CLK_COR_PRECEDENCE_0

CLK_COR_PRECEDENCE_1

Determines whether clock correction or
channel bonding takes precedence when
both operations are triggered at the same
time. Set to TRUE to give clock correction
precedence.

Configurable Clock Correction

CLK_COR_REPEAT_WAIT_0

CLK_COR_REPEAT_WAIT_1

Specifies the minimum number of
RXUSRCLK cycles without clock correction
that must occur between successive clock
corrections.

Configurable Clock Correction

CLK_COR_SEQ_1_1_0

CLK_COR_SEQ_1_1_1

CLK_COR_SEQ_1_2_0

CLK_COR_SEQ_1_2_1

CLK_COR_SEQ_1_3_0

CLK_COR_SEQ_1_3_1

CLK_COR_SEQ_1_4_1

The CLK_COR_SEQ_1 attributes are used
in conjunction with
CLK_COR_SEQ_1_ENABLE to define
clock correction sequence 1.

Configurable Clock Correction

CLK_COR_SEQ_1_ENABLE_0

CLK_COR_SEQ_1_ENABLE_1

Sets which parts of clock correction
sequence 1 are don't cares.

Configurable Clock Correction

CLK_COR_SEQ_2_1_0

CLK_COR_SEQ_2_1_1

CLK_COR_SEQ_2_2_0

CLK_COR_SEQ_2_2_1

CLK_COR_SEQ_2_3_0

CLK_COR_SEQ_2_3_1

CLK_COR_SEQ_2_4_0

CLK_COR_SEQ_2_4_1

Used in conjunction with
CLK_COR_SEQ_2_ENABLE to define the
second clock correction sequence.

Configurable Clock Correction

CLK_COR_SEQ_2_ENABLE_0

CLK_COR_SEQ_2_ENABLE_1

Sets which parts of clock correction
sequence 2 are don't cares.

Configurable Clock Correction

CLK_COR_SEQ_2_USE_0

CLK_COR_SEQ_2_USE_1

Determines if the second clock correction
sequence is to be used.

Configurable Clock Correction

CLK_CORRECT_USE_0

CLK_CORRECT_USE_1

Set to TRUE to enable Clock Correction.

Configurable Clock Correction

CLK25_DIVIDER

Sets the divider used to divide CLKIN
down to an internal rate close to 25 MHz.

CLKINDC_B

Must be set to TRUE. Oscillators driving the
dedicated reference clock inputs must be
AC coupled.

COM_BURST_VAL_0[3:0]

COM_BURST_VAL_1[3:0]

Number of bursts transmitted for a SATA
COM sequence.

TX OOB/Beacon Signaling

Table 1-4:

GTP_DUAL Attribute Summary

(Continued)

Attribute

Description

Section (Page)

«
...
31
32
33
34
35
...
»

Содержание Virtex-5 RocketIO GTP





























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Virtex-5 RocketIO GTP

Бренд: Arteche Страницы: 9

COOPER POWER SERIES

Бренд: Eaton Страницы: 24

COOPER POWER SERIES

Бренд: Eaton Страницы: 32

Бренд: Xblitz Страницы: 76

VOS-8FOM-D232MR

Бренд: Voscom Страницы: 17

Бренд: Mhouse Страницы: 2

Бренд: IBR Страницы: 20

Бренд: BluStream Страницы: 4

Бренд: Dolphin Страницы: 17

u-blox 8NL-8000U

Бренд: Navilock Страницы: 11

Бренд: Sangean Страницы: 12

Бренд: LAUMAS Страницы: 36

Бренд: E+E Elektronik Страницы: 32

Бренд: Boss Audio Systems Страницы: 23

Бренд: Harman Kardon Страницы: 12

Бренд: Icom Страницы: 32

Бренд: STONEX Страницы: 49

Бренд: Audiovox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды