XFP ENGINEERING MANUAL • Approved Document No. DFU1200510 Rev 3 • Page 36 of 36
XFP 16 ZONE ANALOGUE ADDRESSABLE FIRE ALARM PANEL
TECHNICAL SPECIFICATION
Part Nos.
XFP501E/H, XFP501E/X
POWER SUPPLY SPECIFICATION
Mains supply (a.c.) 230V
∿
50/60Hz. Rated current 0.35A r.m.s
Internal power supply 27Vd.c nominal (Ripple voltage 500mV)
Maximum rated current 1.5A @ 230Va.c.
Current specification I max. a = 210mA; I max. b = 1.1A; I min. = 40mA
Maximum internal battery resistance Ri max. = 1.1
Ω
Supply and battery charger monitored for failure Yes
Batteries monitored for disconnection and failure Yes
Batteries protected against deep discharge Yes
Maximum battery size and type 2 x 12V 3.2Ah VRLA type, connected in series.
Use 2 x YUCEL 3.2-12 for LPCB approved systems.
Quiescent current drain (1 loop unloaded) < 50mA
Earth fault monitoring Yes (any conductor)
Temperature compensated charging Yes
LOOP DRIVER SPECIFICATION
Number of loop drivers 1
Line monitored for open and short circuit faults Yes
On-board loop isolators with LED indication when active Yes
Auto-polling from each loop end Yes
Maximum output current per loop 500mA (Voltage: 25V minimum; 34V maximum)
Maximum number of addressable devices 126
Max. number of loop powered sounders per loop @ 10mA 40
Number of programmable sounder groups 16
Number of programmable output sets 16
CONVENTIONAL SOUNDER CIRCUIT SPECIFICATION
Number of programmable circuits 2
End of line resistor value 6800 ohm 5% tolerance 0.25W
Line monitored for open and short circuit faults Yes
Outputs fused at 400mA. Protected by resettable overload circuit
Output voltage 19.5V minimum; 28V maximum
Maximum number of sounders @ 20mA 40
AUXILIARY OUTPUTS
Type Relay voltage free single pole changeover
Maximum switching current 1A
Maximum switching voltage 30Vd.c.
Relay 1 / Relay 2 / Relay 3 Programmed from cause and effect
Fault Active when no faults are present
‘24V’ Aux. power output 19.5V minimum, 28V maximum. Maximum current 100mA. Protected by resettable overload circuit.
AUXILIARY INPUTS
Input 1 Connect to 0V to trigger, Max. input voltage 27V d.c (non-latching). Programmed from cause & effect
Input 2 Connect to 0V to trigger, Max. input voltage 27V d.c (non-latching). Programmed from cause & effect
FUSES
(IEC - EN60127 Pt2)
Primary fuse T 1A H 230V 20mm ceramic
(T=Time Delay, H=High Breaking Current)
Battery fuse F 1.6A, 20mm ceramic
(F = Fast)
PANEL INDICATORS AND CONTROLS
Control buttons Menu, More Information, Silence Internal Sounder, Control Panel Reset, Investigate, Resound
Event scrolling and menu access buttons Up
5
(1), Down
6
(3), Accept
4
(2), Escape
3
(4)
Liquid crystal display Two lines x 40 characters, backlit
Number of zonal LED indicators 16
Other LED indicators (General) Fire, Supply Present, Test, Accessed, General Disablement, Phased Evacuation, General
Fault, Power Supply Fault, System Fault, Sounder Status, Delays Running.
PHYSICAL
Dimensions of panel (W x H x D) 380 x 235 x 90mm (plastic)
Weight (without batteries) 1.8kg
IP rating (to EN60529) IP30
CABLING REQUIREMENTS
Type of cable Fire resistant screened cable, minimum size 1mm
2
Maximum cable length per loop 1km
Connector blocks Plug-on type, largest acceptable conductor size, 1.5mm
2
Maximum allowable loop impedance (each conductor) 20 ohm
Maximum cable capacitance .27µF
NETWORK SPECIFICATION (OPTIONAL)
Connection Via XFP761 network driver fitted in each networked main panel
Maximum no of main panels per network 8
Maximum no of repeaters per non-networked main panel 8
Maximum cable length per network 1km (main panel network); 500m (repeater network)
PC/PRINTER INTERFACE
PC connection Via main panel RS232 molex connector (lead supplied in XFP507 upload/download software kit)
Printer connection Not applicable
OPERATING CONDITIONS
The enclosure is designed for indoor use only. The components are selected to operate within their specification when the environmental conditions
outside the enclosure comply with class 3k5 of IEC 721-3-3. Temperature range: -10
o
C to +40
o
C. Maximum humidity: 95% non condensing.
CERTIFICATES
(Certificates and DOPs are available for download on C-TEC’s website)
LPCB Cert No.: 176b
LPCB Reference Nos.: XFP501E/H (176b/05), XFP501E/X (176b/06)
DOP Nos.: DOP0000035 (XFP501E/H), DOP0000034 (XFP501E/X)
Tested to: EN54-2:1997 + A1:2006 & EN54-4:1997 + A1:2002 + A2:2006 CPR Certificate Nos: 0832-CPR-F1585 (XFP501E/H), 0832-CPR-F1586 (XFP501E/X)
