manualshive.com logo in svg

Xerox Phaser 790DP, Руководство по началу работы, Страница: 8 / 83

Поделиться
Скачать
Xerox Phaser 790DP Скачать руководство пользователя страница 8

Safety Notes, Compliances, Certifications, and other notices

Xerox Phaser 790 Getting Started

viii

WARNING

This is a Class B product.  In a domestic environment this product may
cause radio frequency interference in which case the user may be required
to take adequate measures.

Changes or modifications to this equipment not specifically approved by Fuji
Xerox Australia Limited may void the user’s authority to operate this
equipment.

Shielded cables must be used with this equipment to maintain compliance
with the Radio Communications Act of 1992.

Documentation conventions

The following conventions are used through out the customer documentation.

WARNING

Warnings alert you to operations that could cause personal injury.

CAUTION

Cautions alert you to operations that may cause damage to the machine.

Notes contain additional information, explanations, and helpful suggestions.

Keypoints provide techniques or shortcuts.

Содержание Phaser 790DP




















































































Отзывы:

Нет отзывов