Xerox Phaser 790DP Скачать руководство пользователя страница 15

Страница: 15 / 83

Setting up the Printer Cabinet

1. Setting up the Phaser 790

Xerox Phaser 790 Getting Started

1-5

Setting up the Printer Cabinet (optional)

If you ordered the Printer Cabinet, perform the following steps. If you did not
order the Printer Cabinet, go to the

Installing the 2 Tray Module

procedure.

You will need a phillips screwdriver in order to perform this procedure.

Open the carton containing the Printer Cabinet and ensure that you have
received the following items:

•

Bottom panel with four casters

•

Top panel containing many holes

•

Rear (small) panel

•

Left side panel with hinge attachments on inside front edge

•

Right side Panel without hinge attachments

•

Two hinges

•

Four wood screws

•

12 large screws

•

Two locating pins

•

One u-shaped locking bracket

Locate the bottom panel and lock the four casters.

0301242A -W O L

Содержание Phaser 790DP




















































































Результаты поиска

Содержание Phaser 790DP

Отзывы:

Xerox Phaser 790DP, Руководство по началу работы, Страница: 15 / 83

Результаты поиска

Содержание Phaser 790DP

Отзывы: