Xerox FaxCentre F12 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 380

background image

Service Call Procedures

2-2

3/03

WorkCentre Pro 412, FaxCentre F12 &

WorkCentre M15/M15i

SCP 3 Normal Call Actions

Normal Call Actions are used to determine the reason for the service call.

Procedure

NOTE: If an error message appears at any time. Refer directly to the error code tables in

1-1

Error Codes

RAP, and perform the procedure.

Perform the Following:
1.

Review any defective print or copy samples.

2.

If the LCD is completely blank, switch off the machine. Wait 10 seconds. Switch on the machine. If the
LCD is still blank, go to 7-6 Malfunction, No Power (LCD or LED).

3.

If connected to a network, verify with the customer, that it is permissible to disconnect the machine
from the network.

4.

Check and record the total number of images made by the machine.

5.

Make a note of any parts requiring cleaning or replacement, refer to 7-1 Preventative Maintenance.

6.

Go to SCP4 Fault Analysis.

SCP 4 Fault Analysis

Fault Analysis is used to identify a fault.

Procedure

Exercise the machine in all modes until the fault is determined.
Perform the following:

•

If an error message is displayed, go to 7-2 Diagnostics.

•

If an image defect is evident, go to 7-3 Scanner.

•

If there are problems in sending or receiving FAXs, go to 7-4 FAX.

•

If a print defect is evident, go to 7-5 Print Quality.

•

If the machine is malfunctioning, go to 7-6 Malfunction.

•

When the fault is corrected, go to SCP 5 Final Actions.

SCP 5 Final Actions

Final Actions are used to evaluate the total operation of the system and to identify the actions required to
complete the service call.

Procedure

Complete the following:

•

Perform any remaining cleaning or replacement actions, referred to in SCP 3.

•

Exercise the machine in all modes, making copies and / or prints from all trays, utilising the ADF
and the document glass.

•

If necessary, make a proof copy of a customer document.

•

Remove and destroy any copies of test patterns.

•

Provide customer training if required.

•

If any of the customers selections were changed, return them to the customers preferred settings.

•

Complete all administrative tasks.

Ensure the machine and service area are clean before leaving the customer premises.

«
...
22
23
24
25
26
...
»

Содержание FaxCentre F12





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FaxCentre F12

image Prograf iPF785 Series

Бренд: Canon Страницы: 136

Бренд: GBC Страницы: 110

Бренд: Xerox Страницы: 89

Бренд: Canon Страницы: 37

imageRUNNER ADVANCE C5255

Бренд: Canon Страницы: 64

Powershot A3100 IS

Бренд: Canon Страницы: 6

imagePROGRAF TC-20

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 88

Бренд: Oki Страницы: 44

Бренд: Xiamen Hanin Electronic Technology Страницы: 62

Бренд: Triumph Adler Страницы: 4

Бренд: Oce Страницы: 268

Бренд: Xerox Страницы: 78

Бренд: Oki Страницы: 20

Perfecta 2400STP

Бренд: Variquest Страницы: 12

ScreenWriter Colour ScreenWriter

Бренд: Xante Страницы: 446

Бренд: Hitt Marking Devices Страницы: 27

Бренд: Konica Minolta Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды